久久久影院,日韩在线小说一二三四播放在线,日麻批的黄色录像,无码中字逼逼

泰安揚帆數控科技有限公司為您提供等相關信息發布和資訊展示,敬請關注!
咨詢服務熱線:
13345281377

新聞資訊

產品

行業新聞

自動焊接設備故障維修之直接短接法

來源:http://www.fx361.com.cn/  發布時間:2022-07-28 瀏覽次數:0

設備電路或焊接設備的故障大致歸納為短路、過載、斷路、接地、接線錯誤、焊接設備的電磁及機械部分故障、元器件老化等七類。諸類故障中出現較多的為斷路故障,包括導線斷路、虛連、松動、觸點接觸不良、虛焊、假焊以及熔斷器熔斷等。
The faults of equipment circuit or welding equipment can be roughly divided into seven categories: short circuit, overload, open circuit, grounding, wrong wiring, electromagnetic and mechanical part faults of welding equipment, aging of components and parts. Many of these faults are open circuit faults, including wire open circuit, virtual connection, looseness, poor contact of contacts, false soldering, false soldering and fuse fusing.
山東自動焊接設備的這類故障除用電阻法、電壓法檢查外,還有一種更為簡單可靠的方法,就是短接法。即用一根良好絕緣的導線,將所懷疑的斷路部位短路接起來,如短接到某處,電路工作恢復正常,說明該處斷路。具體操作可分為局部短接法和長短接法。
In addition to the resistance method and voltage method, there is a simpler and more reliable method to check such faults of Shandong automatic welding equipment, that is, the short-circuit method. That is, use a well insulated wire to short-circuit the suspected open circuit part. If it is short circuited to a certain place, the circuit will return to normal, indicating that there is an open circuit. The specific operation can be divided into local short connection method and long short connection method.
對于連續燒壞的元器件應機明原因后再進行更換;電壓測量時應考慮到導線的壓降;不違反設備性能和焊接設備作用的原則,修復的焊接設備初次試通電工作前,
The components and parts that are continuously burnt out shall be replaced after the cause is found out; The voltage drop of the conductor shall be considered during voltage measurement; Do not violate the principle of equipment performance and the role of welding equipment. Before the first trial energization of the repaired welding equipment,
山東自動焊接設備
對氣體保護焊和點焊、縫焊、凸焊及對焊等設備應該先通氣、通水,應該加油的部位還需要加油,周圍障礙物,通電工作時手不得離開電源開關停止按鈕,保險期間應使用等量或略小于額定值的電流;還須注意測量儀器儀表擋位的選擇。
Gas shielded welding, spot welding, seam welding, projection welding, butt welding and other equipment should be ventilated and watered first. The parts that should be oiled also need to be oiled, and the surrounding obstacles should be removed. When working with power on, hands should not leave the power switch stop button. During the insurance period, the same amount of current or slightly less than the rated value should be used; Attention should also be paid to the selection of gear of measuring instruments.
以上一些檢查方法,要視情況靈活運用,但須遵守操作規章,防止在設備維修過程中出現人身、設備傷害事故,并且盡可能兩人操作和監護。
The above inspection methods should be used flexibly according to the situation, but the safety operation rules must be observed to prevent personal and equipment injury accidents in the process of equipment maintenance, and two people should operate and monitor as much as possible.
對焊接設備故障的檢查和維修排除,要按照相關要求做好記錄。方便以后類似故障發生后的檢查、日常維護保養和故障排除的經驗積累,更多相關內容就來我們網站http://www.fx361.com.cn咨詢了解吧。
The inspection, maintenance and troubleshooting of welding equipment shall be recorded according to relevant requirements. It is convenient to accumulate experience in inspection, daily maintenance and troubleshooting after similar faults occur in the future. More relevant content can be found on our website http://www.fx361.com.cn Consult and understand.

上一篇:焊接機械手操作及保養規程
下一篇:維修時應詳細觀察焊接設備本身

黑人hd| 欧乱色国产精品兔费视频 | 办公室被绑奶头调教羞辱OL| 免费无码av片在线观看| 狠狠的干性视频| 久精品视频| 国产美女一级特黄大片| 福利视频一区| 国产精品久久久精品三级网站 | 五月av| 国产伦精品一区二区三区妓女| yy111111少妇影院免费观看 | 亚洲精品无码av天堂| 嘉义县| 久久伊人热| 伦一理一级一a一片| 亚洲另类精品无码专区| 人妻丰满熟妇av无码区| 国产成人a区在线观看| 精品亚洲AⅤ在线观看| 无码少妇一区二区| 徐闻县| 日本精品一区| 国产精品精品久久久久久| 思思在线| 无码专区久久综合久综合字幕 | 国产成人亚洲综合二区| 亚洲人成网站在线播放2019| 成人免费一区二区三区| 亚洲熟妇久久精品| 软萌小仙自慰粉嫩小泬网站| 贺兰县| 梨树县| 久久精品国产欧美亚洲人人爽| 午夜三区| 一区二区三区美女| 79久久精品熟女人妻| 男人添女人下部高潮全视频| 无码视频| 欧美猛男男办公室激情| 亚洲乱人伦中文字幕无码|