數控切割機在切割能源和數控控制系統兩方面取得了長足的發展，切割能源已由單一的火焰能源切割發展為多種能源，那么山東數控焊接設備廠家就來為您講講數控切割機的正確使用吧。

CNC cutting machine has made great progress in cutting energy and CNC control system. Cutting energy has developed from single flame energy cutting to multiple energy sources. Then Shandong CNC welding equipment manufacturer will tell you about the correct use of CNC cutting machine.

1、合上配電柜內開關;

1. Close the switch in the distribution cabinet;

2、打開操作面板上電源鎖，按下電源按鈕，給CNC供電;接通除塵器電源，檢查控制箱面板上的指示燈是否正常;

2. Open the power lock on the operation panel and press the power button to supply power to the CNC; Turn on the power supply of the dust collector and check whether the indicator light on the control box panel is normal;

3、CNC進行內部自診斷，確認沒顯示錯誤信息;

3. CNC conducts internal self diagnosis and confirms that no error information is displayed;

4、合上伺服柜內的開關，按下操作面板上的伺服開按鈕，給伺服系統供電，轉動控制柜面板上脈沖旋鈕開的位置對濾筒進行反沖，檢查脈沖是否正常;

4. Close the switch in the servo cabinet, press the servo on button on the operation panel to supply power to the servo system, turn the pulse knob on the control cabinet panel to the on position to recoil the filter cartridge, and check whether the pulse is normal;

5、試操作，確認面板上的各開關、按鈕靈活、可靠檢查卸灰插板閥是否正常;

5. Test operation, confirm that the switches and buttons on the panel are flexible and reliable, and check whether the ash unloading plug-in valve is normal;

6、試運行機器，確認機器運行平穩，各限位及緊急按鈕可靠;

6. Test run the machine and confirm that the machine runs smoothly and that the limit and emergency buttons are reliable;

7、噴粉劃線在切割前進行，注意鋅粉易爆，注意避免飛揚，

7. Powder spraying and scribing shall be carried out before cutting. Pay attention to the explosion of zinc powder and avoid flying,

8、等離子切割時，需要注意在自動點火時，人員要遠離點火高壓線圈;

8. During plasma cutting, attention shall be paid to keep personnel away from ignition high-voltage coil during automatic ignition;

手動將割炬定到起始位置;在CNC上選定切割程序，并完成工作配置:切割速度、割縫補償?shù)葍?nèi)容;按“GO”按鈕開始切割;按操作說明書對切割中出現的不同問題，進行相應處理，直到切割完成。更多相關事項就來我們網站http://www.fx361.com.cn看看吧。

Manually set the cutting torch to the starting position; Select cutting program on CNC and complete work configuration: cutting speed, slit compensation, etc; Press the "go" button to start cutting; According to the operating instructions, different problems in cutting shall be handled accordingly until the cutting is completed. For more information, please visit our website http://www.fx361.com.cn Let's see.